1 / 4
Overview
- Make
- COE
- Model
- CPRF 660
- Type
- Coil Feed Lines
- Condition
- Used
- Stock #
- 502059
Spec Sheet
ITEM No.1 - CPRF 660
COE Servo Roll Feed 60" Wide
MATERIAL SPECIFICATIONS
M.C.R.S. - Max: 0.125" thick @ 60.00" wide
M.C.R.S. - Min: 0.030" thick @ 60.00" wide
PASS LINE: 59"
ROLL FEED SPECIFICATIONS:
Number of Rolls 2
Roll Diameter 6"
Full Body Width 60"
Drive Ratio 6.5:1
Acceleration 30 Feet/Sec/Sec
Roll Speed 240 Feet/Minute
Feed Accuracy +/- 0.003"
ROLL FEED STANDARD FEATURES:
- Sealed Precision Roller Bearings
- Upper and Lower Feed Rolls With #3 Crodon Chrome Finish
- 230/460 Volt AC Three Phase Supply Voltage
- 3 Roll Catenary Support Section With Full Sideplates and Funnels
- Air Pressure Regulator for Exact Feed Roll Pressure
- Cluster Gear Driven Upper Feed Roll With Mating Splined Shafts and Gears
- Dual Roll Hand Crank Edge Guides with Self Centering & Independent Adjustment
- Emergency Stop Push Button
- Fused Electrical Safety Disconnect
- Heavy Duty Cabinet Base with Press Mount Brackets & +/- 6" of Height Adjustment
- High Performance Maintenance Free AC Brushless Servo Motor
- Remote Jog Pendant
- Rigid Machined Tie Bar Construction for Precise Assembly
- Single Cycle Pushbutton for Set-up at Jog Speed
ROLL FEED STANDARD OPTIONS
- Motorized Passline Adjustment
- Air Operated Anti-Backup Roller Assembly
- Full Width upper and Lower Feed Rolls
ITEM No. 2 - CPTT 6015
COE 60" x 15' Dual Threading Table
PASS LINE: 59"
THREADING TABLE STANDARD FEATURES:
- Heavy Duty Steel Solid Top Construction
- Thread Table Length
- Adjustable Passline Feature
- Air Raise and Lower of Threading Table
- Dual Sided Table Construction
ITEM No.3 - CPPS 305 60
COE 3.00" x 60" Straightener w/5" Pinch
POWER STRAIGHTENER STANDARD FEATURES:
- Rigid Tie Bar Construction of Straightener Head
- 230/460 Volt AC Three Phase Supply Voltage
- 3 Roll Catenary Section Assures Proper Material Support
- Air Cylinder Raise and Lower of Upper Pinch Roll
- Central Point Lubrication System
- Crodon Coated Upper and Lower Entrance Pinch Rolls
- Electrical Safety Disconnect
- Independent Adjustment of Upper Straightener Rolls
- Remote Jog Pendant for Material Threading
POWER STRAIGHTENER STANDARD OPTIONS:
- 30 Horsepower AC Variable Speed Drive - Digital Control
- PLC Controls and Operator Touchscreen
- Digital Upper Straightener Roll Height Indicators
- Double Row Upper and Lower Straightener Backup Rollers
- Hand Crank Entrance Edge Guides
- Peeler/Threader/Hold Down Station with Motorized Endwheel
- Reel to Straightener Tie in Brackets
- Remote Jog Pendant for Material Threading
- Ultra Sonic Variable Speed Loop Control with 3 Position Selector Switch
POWER STRAIGHTENER SPECIAL OPTIONS;
- Motorized Straightening Roll Adjustment - Each Straightening Roll Is Adjusted by a Motor and Controlled by the Automation Package Per the Selected Job Program
ITEM No.4 - CPTR - PO 40060
COE 40,000# 60" Traveling Reel
COIL REEL SPECIFICATIONS:
Max. Coil Weight 40,000 Lbs
Max. Coil Width 60"
Max. Coil O.D. 72"
Expansion Range 19.25-24.75"
TRAVELING COIL REEL STANDARD FEATURES:
- Bearing Tube Support of Mandrel
- Heavy Duty Welded Steel Construction
- Three (3) Pad Mandrel Construction
- Hydraulic Mandrel Expansion Feature
- Hydraulic Threading Drive Feature
- Material Width Scales on Mandrel Pads
TRAVELING COIL REEL STANDARD OPTIONS
- Fail Safe Drag Brake to Prevent Coil Over Run
- Full Radius Mandrel Pads with Matching Keepers
- Full O.D. Backplate - 72" Maximum Coil O.D.
TRAVELING COIL REEL SPECIAL OPTIONS:
- Stationary Load V-nest
The stationary V-nest will have 18" of vertical lift. The coil reel will travel to the V-nest to pick-up the coil.
- Traveling Coil Reel
The coil reel will travel to the stationary V-nest to load the coil. The automation package will then move the reel to the centerline based on programmed coil width. The coil will always be loaded against the back plate.
Similar Equipment
#502060
#502058
